Outline · [ Standard ] · Linear+ Card Frames, taking orders

[Krusin]

For the newbie's & those that don't know I build Custom Card Frame's for members. It's a design I came up with after years of trial & error to develope a way to display my collections.

Examples-
Krusin's frame pic's



I mainly use Oak & Red Oak wood for the frames. If your interested in one let me know what you might like & if it's not listed in the example pricing I'd be happy to work up a free quote for you.

Just an fyi I can do frames for amlost any type holders including graded cards. You can also get either horizontal, vertical or a mixed display as far as orentation goes. If you have something special in mind I'd
be happy to discuss that with you also.

thanks,
-------------------------------------------------------------------------------------
CP Pricing, These prices are for either Screw Downs or Mag. Holders only & one orentation
either all standing or all laying.

20 Cards, 4 cards x 5 rows - 123.00

20 Cards, 5 cards x 4 rows - 115.50

25 Cards, 5 cards x 5 rows - 144.00

30 Cards, 6 cards x 5 rows - 157.50

30 Cards, 5 cards x 6 rows - 165.00

36 Cards, 6 cards x 6 rows - 189.00

40 Cards, 8 cards x 5 rows - 196.50

40 Cards, 5 cards x 8 rows - 220.50

50 Cards, 10 cards x 5 rows - 236.00

Shipping depends on size & where it's being shipped to.
-------------------------------------------------------------------------------------

[HOFerAutoCollector]

definitely interested.

[msuwendy]

Bud....I would definitely be interested in getting a frame or two from you....but am worried about how much it would cost to ship them to Malaysia

Would it be possible to get a quotation for say a frame that can fit 20 standard single-screw screwdowns lying horizontally in 4 rows?

[wrv01]

let me know when the prices are up thanks

[NGWH Sports Cards]

I might want one!

[mikeyb]

Quick question for you.

How do the cards stay were there put? Do you put a piece of glass on the front or is the inside pieces of wood slotted?

Mike

[Krusin]

Quick question for you.

How do the cards stay were there put? Do you put a piece of glass on the front or is the inside pieces of wood slotted?

Mike

Hey Mike,

Just found your question. No glass on the front, the holders go in & out really easy. The won't fall out because of of a small lip on the bottom & a deeper one on top. You put the cards in top 1st, then in & down kind of like how the gas station price signs work. It took me a while to get it to work just right but I've prefected it for any type of holder.

If your interested in one let me know via a PM as I got lucky to find your ? today.

thanks

[mikeyb]

Im thinking about it, I wasnt sure if you had to take the side trim off and slide them all in from the side, and the trim was held on with dowels, but I understand the concept now.

Possibly might be interested sometime, do you make like just a 4 card screwdown holder?

Mike

[Krusin]

Im thinking about it, I wasnt sure if you had to take the side trim off and slide them all in from the side, and the trim was held on with dowels, but I understand the concept now.

Possibly might be interested sometime, do you make like just a 4 card screwdown holder?

Mike

Hey Mike,

You name it I'll build it. It's a bit too cold at the moment but I'm cranking to get started again. I'm planning on building non-stop till the Nationals where I'm sharing a table with some friends. If they go over well there I'm thinking about changing what I do for a living. As you can tell by my scans I've built a few now even shipped 3 over to England for a member who's going to order more for his sets.

thanks

[champb21]

dang you got some nice ones made i might get one when i get money it be for a set of like 5 cards.

[psujds389]

I've got something unique in mind. a way to display some of my nicer cards around the outside, while displaying a few baseballs in the middle. the problem is that i have an assortment. graded and non. dunno how we could get around that and keep a solid fit.